Barco DATA 708 Installationshandbuch

R9002129INSTALLATION MANUALDATA708

Unpacking and Dimensions2-2 5975987A BARCODATA 708 260597Projector dimensions(mm)

Installation Guidelines3-15975987A BARCODATA 708 2605973INSTALLATION GUIDELINESInstallation guidelinesCareful consideration of things such as image si

Installation Guidelines3-2 5975987A BARCODATA 708 260597* Where to install the projector?To indicate a correct installation position it is necessary t

Installation Set Up1-15975987A BARCODATA 708 2605974INSTALLATION SET UPAccess to controlsOpening procedure :During the projector set up and installati

Installation Set Up4-2 5975987A BARCODATA 708 260597Scan adaptationThe scanning can be switch by turning the Horizontal and Verticalscan connectors an

Installation Set Up1-35975987A BARCODATA 708 260597A : Horizontal scan inversionThree connectors are used, one for each horizontaldeflection coil. Wh

Installation Set Up4-4 5975987A BARCODATA 708 260597

Projector Set Up5-15975987A BARCODATA 708 2605975PROJECTOR SET UPProjector Set UpThe strap on the CPU unit allow a set up of the password mode.Gaining

Projector Set Up5-2 5975987A BARCODATA 708 260597

Power Connection6-15975987A BARCODATA 708 2605976POWER CONNECTIONPower (mains) cord connectionUse the supplied power cord to connect your projector to

Power Connection6-2 5975987A BARCODATA 708 260597

Installation Adjustments7-15975987A BARCODATA 708 2605977INSTALLATION ADJUSTMENTSEntering the adjustment modeADJUSTMENT MODESelect a path frombelow:Se

Installation Adjustments7-2 5975987A BARCODATA 708 260597Overview flow chart installation mode.SCHEIMPFLUG ADJUSTMENT <ENTER> to continue<EXI

Installation Adjustments7-35975987A BARCODATA 708 260597ADJUSTMENT MODESelect a path frombelow:Select with or then <ENTER> <EXIT>

Installation Adjustments7-4 5975987A BARCODATA 708 260597Scheimpfug adjustmentThe scheimpfug correction can be adjusted separately for the threetubes

Installation Adjustments7-55975987A BARCODATA 708 260597Optical lens focusingOPTICAL LENS FOCUSING<ENTER> to continue<EXIT> to return1. LO

Installation Adjustments7-6 5975987A BARCODATA 708 260597Raster centeringThe raster must be centered on the CRT screen surface of each tube,therefore,

Installation Adjustments7-75975987A BARCODATA 708 260597CRT projection angle adjustmentThe projection angle of the red and blue CRT's is dependen

Installation Adjustments7-8 5975987A BARCODATA 708 260597Loosen the four hexagon screws A, A', B and B', upper and lowerfixation latch. The

Installation Adjustments7-95975987A BARCODATA 708 260597ADJUSTMENT MODEsource 1Select with or then <ENTER> <EXIT> to returnGUIDED

BARCO PROJECTION SYSTEMSDate :260597Art. No. :R5975987AR9002129INSTALLATION MANUALDATA708

Installation Adjustments7-10 5975987A BARCODATA 708 260597

G2 AdjustmentA-15975987A BARCODATA 708 260597AG2 ADJUSTMENTEnter the adjustment mode by pressing ADJUST and highlightService. Press ENTER to start up

G2 AdjustmentA-2 5975987A BARCODATA 708 260597A green LED for each color is mounted on the driver board, below theCRT's. When selecting the G2 a

FORMULAOUTSIDE PACKAGE DIMENSIONS (Inches)CHEMICAL FAMILYFEDERAL STOCK NUMBER (FSN)GROSS WEIGHT (LBS)%TRESHOLD LIMITVALUE (Units)ALLOYS AND METALLIC C

STABILITYUNSTABLESTABLECONDITIONS TO AVOIDINCOMPATABILITY (Materials to avoid)HAZARDOUS DECOMPOSITION PRODUCTSHAZARDOUSPOLYMERIZATIONWILL NOTOCCURCOND

Due to constant research, the information in this manual is subject to change without notice.Produced by BARCO NV, May 1997.All rights reserved.Tradem

Table of Contentsi-15975987A BARCODATA 708 260597TABLE OF CONTENTSiWARNINGS ...

Table of Contentsi-2 5975987A BARCODATA 708 260597

Safety Instructions1-15975987A BARCODATA 708 260597WARNINGTO PREVENT FIRE OR ELECTRICAL SHOCKHAZARD, DO NOT EXPOSE THIS EQUIPMENT TORAIN OR MOISTUREFE

Safety Instructions1-2 5975987A BARCODATA 708 260597 Power cord with ANSI 73.11 plug:The wires of the power cord are colored inaccordance with the fol

Unpacking and Dimensions2-15975987A BARCODATA 708 2605972UNPACKING AND DIMENSIONSUnpackingTake the projector out of its shipping carton and place it o