Barco E-2320 C (SE) Bedienungsanleitung

Installation & User ManualE-2320 C

Preface10 E-2320 CVentilationDo not cover or block the ventilation openings in the cover of the set. When installing the display in a cupboard or anot

PrefaceE-2320 C 11Explanation of symbolsSymbols on the display and / or power supplyOn the display or power supply, you may find the following symbols

Preface12 E-2320 CSymbols used throughout the manual:Warning CautionImportant notice or remarkNoteHint, tip Additional information

IntroductionE-2320 C 13IntroductionOverviewThank you for choosing Barco.Single display or complete system?This manual describes installation and usage

Introduction14 E-2320 CPower savingThe display is equipped with a power saving system. When left idle for a certain time, the computer connected to th

IntroductionE-2320 C 15• Digital video (DVI) cable (25-pins)• Analog video (VGA) cable (15-pins)•USB cable• Two velcro strips to bind the cables• Eur

Introduction16 E-2320 C1. Control wheelThe control wheel can be pressed like a push button and rotated like a knob.It allows to put the display in sta

IntroductionE-2320 C 172. Tilt & swivel foot coverThis cover is packed in a separate box when the display is shipped to the customer.3. Tilt &

Installation18 E-2320 CInstallationPrecautions• Keep your original packaging. It is designed for this display and is the ideal protection during trans

InstallationE-2320 C 19Figure 3To remove the clip:1. Position the display with its rear side facing you.2. Pull the red clip out of the fixation holes

(This page intentionally left blank.)2 E-2320 C(This page intentionally left blank.)

Installation20 E-2320 CFigure 43. To change from landscape to portrait, turn the panel clockwise.Figure 54. To change from portrait to landscape, turn

InstallationE-2320 C 21Power connectionTo connect the power:1. To get access to the connectors, remove the connector compartment cover by pulling down

Installation22 E-2320 C4. Connect the other end of the power cord to a grounded power outlet.We recommend to use an additional surge protector between

InstallationE-2320 C 23Connecting DVI signals: Two displays:1. Connect the left display (when looking at the front side) to Vid 1 as described above.2

Installation24 E-2320 CUSB connectionIf the display receives video from a Barco-supported display controller, it is not necessary to establish a USB c

InstallationE-2320 C 25• Put the connector compartment cover back on the display. Pay attention that the signal cables are positioned under the bulge

Installation26 E-2320 CAttaching the display to an armThe panel, standard attached to the tilt & swivel foot, is compatible with the VESA 100 mm s

InstallationE-2320 C 276. Remove the four screws fixing the foot while supporting the foot.7. Attach the arm stand firmly to the panel using 4 screws

Installation28 E-2320 C4. After reading the Software License Agreement on the next screen, click “I accept...” and “Next” to continue.5. Enter your cu

OperationE-2320 C 29OperationDisplay operationOperating precautionsContinuous operation of the display with the same image may result in some image st

E-2320 C 3Copyright noticeThis document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or copied

Operation30 E-2320 COn-screen displayAbout the on-screen displayThe on-screen display (OSD) has a hierarchical structure, with several levels. The top

OperationE-2320 C 312. To enter into a menu or move to a lower level of the menu structure, rotate the control wheel to select the desired menu. Next,

Operation32 E-2320 C• In case you notice the image geometry or positioning is not as desired.Required test patternTo obtain good results, the image on

OperationE-2320 C 332. Rotate the control wheel to select Adjustments.3. Press the control wheel to enter the Adjustments menu.4. Rotate the control w

Operation34 E-2320 CTo adjust Contrast:1. Rotate the control wheel to display the on-screen display. The Main Menu appears.2. Rotate the control wheel

OperationE-2320 C 35To adjust brightness:1. Rotate the control wheel to display the on-screen display. The Main Menu appears.2. Rotate the control whe

Operation36 E-2320 C3. Press the control wheel to enter the Settings menu.4. Rotate the control wheel to select Color Temp.5. Press the control wheel

OperationE-2320 C 376. Exit the menus and save the changes.To enable user controls:1. Do not use the control wheel for at least 3 seconds.2. Rotate th

Operation38 E-2320 CComplete OSD overviewMain menuAutosetThe Autoset menu is not available in DVI mode.Name Description Presentin DVI modeAutoset Allo

OperationE-2320 C 39When do you need to use the Autoset function?• The first time you use the display with analog video connected.• After connecting o

4 E-2320 C(This page intentionally left blank.)

Operation40 E-2320 C• Automatic Geometry: The edges of the image should have an intensity of at least 15% video amplitude. .• Automatic Phase: The ima

OperationE-2320 C 41Adjustments: GeometryAdjustments: PhaseThis menu is not available in DVI modeName Description Availablein DVI modeAutomaticGeometr

Operation42 E-2320 CInput Selection SettingsName DescriptionAuto Automatically selects the input to which a video signal is connected. If more than on

OperationE-2320 C 43Information - General Information:Information - Current Input Format:Automatic Menu Exit Switch the automatic menu exit feature on

Operation44 E-2320 CNioWatch softwareIntroductionTo use NioWatchThe NioWatch application resides in the Windows systray. To use one of the NioWatch fu

OperationE-2320 C 45Display settingsGeneralFigure 18: Display Settings dialogThe numbered icons in the upper part of the dialog represent the display

Operation46 E-2320 Cdisplay controller head. In that way you can easily see which display is connected to which head.The Display tab allows to view in

OperationE-2320 C 47to this calibration. If no former calibration was found, default factory settings are selected.When you restart NioWatch, the last

Operation48 E-2320 C• To select another color temperature, select an item from the Color Temperature drop-down box. This function is available for E-2

OperationE-2320 C 49Graphic Board tabFigure 19: Graphic Board tabHere you can see information about the installed display controller: Name, serial num

Table of ContentsE-2320 C 5Table of ContentsPreface ...

Operation50 E-2320 CCalibration tabFigure 20: Calibration tabHere you can calibrate display(s), revert to the latest calibration, revert to default fa

OperationE-2320 C 512. If you have multiple Nio displays of the same type connected (multi-head system), consider if you wish to equalize the display

Operation52 E-2320 C5. Follow the guidelines on the screen to complete the calibration successfully.Note:If the Equalization option is set in the Appl

OperationE-2320 C 532. In the Calibration dialog (see step no. 3. in the description of the calibration with sensor), check the option Visually and cl

Operation54 E-2320 C3. In the next dialog box, select option Reset to the latest user calibration and click OK.The calibration and the luminance will

OperationE-2320 C 55Test patternsTest PatternsFigure 24: Test Patterns dialog1. Select the desired test pattern by clicking on the corresponding thumb

Operation56 E-2320 CApplication settingsGeneral tabFigure 25Here you can check the option “Only administrators have full access”.When this option is c

OperationE-2320 C 57Calibration tabFigure 26: Calibration tabEqualizationHere you can check the Equalization option, allowing you to match all the dis

Operation58 E-2320 CFigure 27: Dual-head equalizationNote: The Equalization option will be available only if the system contains at least two Nio disp

OperationE-2320 C 59MediCal Administrator tabFigure 28: MediCal Administrator tabHere you can connect to MediCal Administrator, if present.To connect

Table of Contents6 E-2320 CTest patterns ... 55Application settings ...

Operation60 E-2320 CTo update NioWatch:Select Update NioWatch from the Start > Programs > Barco NioWatch menu.The application will search via th

CleaningE-2320 C 61CleaningPrecautions• Take care not to damage or scratch the glass or LCD panel.• Do not apply pressure on the glass or LCD panel.•

Cleaning62 E-2320 CTo clean the LCD panel:• Dust particles on the LCD panel may be blown away by using a dust remover. E.g., DUST OFF 67 (KONTAKT Chem

TroubleshootingE-2320 C 63TroubleshootingGeneral tips• If one display from a multi-head system exhibits problems, try to eliminate the problem by swit

Troubleshooting64 E-2320 CProblems and solutionsProblem description Possible tests or solutionsScreen remains black • Please check the installation pr

TroubleshootingE-2320 C 65Image contains not enough grayscales• Adjust the Display Function to DICOM by means of the NioWatch software• You may have i

Troubleshooting66 E-2320 CNote: What if the graphic board resolution is too lowSome non-Barco graphic boards (e.g., single-link boards) may have an in

TroubleshootingE-2320 C 676. Reboot the computer.After reboot, the signal from the graphic board should now be visible on the display.

Technical Information68 E-2320 CTechnical InformationTechnical specificationsE- 2320 C:Item SpecificationPicture panel 20.1-inch diagonal viewable scr

Technical InformationE-2320 C 69Input signals Possible resolutions:• 640 x 480 @ 60, 75, 85, 100 Hz• 800 x 600 @ 60, 75, 85, 100 Hz• 1024 x 768 @ 60,

PrefaceE-2320 C 7PrefaceNoticeAlthough every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for err

Technical Information70 E-2320 CConnector pin assignmentsDVI connector:Figure 29: DVI connector pin layoutPin no. Signal Pin no. Signal1 TMDS DATA 2-

Technical InformationE-2320 C 71D-Sub 15 connector:Figure 30: D-Sub 15 pin layoutGlossaryCalibrationEach display is calibrated in the factory before i

Technical Information72 E-2320 CDisplay FunctionA Display Function describes how a display device converts the video signals at the inputs into light.

Technical InformationE-2320 C 73Presets and Internal memory systemThe memory of the display contains maximum 200 fixed and 28 programmable Presets. Wh

Warranty Statement74 E-2320 CWarranty StatementARTICLE 1: SERVICESBarcoView warrants that the equipment will be free of defects in workmanship or mate

Warranty StatementE-2320 C 75center) shall become the property of BarcoView (or the authorized service center).1.5 The repaired equipment shall be ret

Warranty Statement76 E-2320 Cobligations under this paragraph shall excuse BarcoView's performance hereunder:3.1 Customer shall not expose BarcoV

Warranty StatementE-2320 C 77products or services covered by or furnished under this warranty condition, whether arising out of contract, negligence,

www.barco.comB4100529 - 02July 2007

Preface8 E-2320 CCanadian noticeThis Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la Classe A est conforme à la

PrefaceE-2320 C 9Degree of safety (flammable anesthetic mixture):Equipment not suitable for use in the presence of a flammable anesthetic mixture with